| |
Special Production Request
Required for Ordering
Please do not hesitate to contact us for any support
issues. This trainer range is now discontinued and
only available on special production request.
Please see our newer product range
for alternate. This range is based on linear power
supply and single sided board with reverse side
jumpers |
|
 |
|
-
Parallel Port
A 25-pin male
jack for connecting to the
parallel port of a PC.
- Pin
Out Socket
A 25-pin female socket for
extending input/output of
parallel port to connections on
the trainer.
- Range
Knob
for selecting the frequency
range of the function generator
waveform out of 100Hz, 1KHz,
10KHz and 100KHz.
-
Amplitude Knob
for varying the amplitude of the
function generator output
waveform.
-
Function Knob
used to select one of the three
output waveform types: sine,
square and triangular.
-
Waveform Socket
for function generator output
waveform.
- Clock
Socket for clock generator
output.
- Logic
Switches
Six logic
switches for providing TTL logic
levels high (5V) and low (0V) at
the corresponding output point
of the sockets.
-
Digital Input/Output Six sockets
for output of the logic switches
and providing logic input.
- Bread
Board
For electronic/digital circuit
patching.
- Seven
Segment Display.
- BCD
Input
for 7-segment
display.
-
Speaker Volume Control
.
- Probe LED’s
Two LED’s for indicating TTL
High or Low levels picked up by
the logic probes.
-
Speaker In
Female socket of 10 connections
for connecting an input to a
speaker on the trainer.
- Mic
In
Female sockets of 10 connections
for connecting to the output of
a Mic on the trainer.
-
Temperature Sensor
Reads
temperature in degrees Kelvin
with scale of 10mV/şK.
Temperature OUT can be taken
from the 10-pin female socket
placed adjacent to the
temperature sensor.
- GND
Socket
for ground.
- - 12VDC
Socket for -12VDC±10% fixed.
- - 5VDC Socket
for -5VDC±10% fixed.
- +12VDC Socket
for +12VDC ±10% fixed.
- +5VDC Socket
for +5VDC±10% fixed.
- Reset.
-
Micro-controller Socket
to house the Atmel 89C5x series
micro-controller with sockets to
extend its pin connections to
the breadboard.
-
RS-232 port
for serial interface to a PC
serial port.
- TX, Rx, RTS
Pin out of RS-232 for extension
elsewhere on the trainer.
-
Trigger
H-->L and L-->H triggers by
pressing the keys.
- To
PC- Mic/Line In
Jack for SounDAQ interface.
- From
PC-Speaker
Out Jack for SounDAQ interface.
- L-Spk
Volume control for LHS speaker.
- R-Spk
Volume control for RHS speaker.
- Digital Gain
Three selector switches for
selecting gain in 3-bit binary
form of the channel selected by
the Multiplexer.
-
Channel Selector
Two selector switches for
selecting 2-bit binary number of
channel.
- Differential
Analog Inputs Channels Input of
Analog Multiplexer.
-
Signal Conditioning
for the multiplexed channel.
- PC
Speaker Interface
For SoundDAQ Interface for Left
and Right speakers of PC.
- Input A/D
Input of Analog to Digital
Converter.
-
Acquisition Data acquisition
block.
-
Anti-Aliasing Filter.
-
Analog To Digital Socket
for extending digital output of
ADC.
-
Digital To Analog Input socket
for Digital to Analog Converter.
-
Potentiometer
0 to 80K?+20% variable resistor.
-
Digital To Analog Output Socket
for extending output of DAC.
-
Relay:
One electronic relay that
operates with 5VDC.
- Logic
Probe:
Two logic probe connections.
|
|
|
|
|
